View ISL9N302AS3ST_566308.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

ISL9N302AS3ST
April 2002
ISL9N302AS3ST
N-Channel Logic Level PWM Optimized UltraFET(R) Trench Power MOSFETs
General Description
This device employs a new advanced trench MOSFET technology and features low gate charge while maintaining low on-resistance. Optimized for switching applications, this device improves the overall efficiency of DC/DC converters and allows operation to higher switching frequencies.
Features
* Fast switching * rDS(ON) = 0.0019 (Typ), VGS = 10V * rDS(ON) = 0.0027 (Typ), VGS = 4.5V * Qg (Typ) = 110nC, VGS = 5V * Qgd (Typ) = 31nC * CISS (Typ) = 11000pF
Applications
* DC/DC converters
DRAIN (FLANGE) D GATE SOURCE G S
TO-263AB MOSFET Maximum Ratings TA = 25C unless otherwise noted
Symbol VDSS VGS Parameter Drain to Source Voltage Gate to Source Voltage Drain Current Continuous (TC = 25oC, VGS = 10V) ID Continuous (TC = 100oC, VGS = 4.5V) Continuous (TC = 25oC, VGS = 10V, R JA = 43oC/W) Pulsed PD TJ, TSTG Power dissipation Derate above 25oC Operating and Storage Temperature 75 75 28 Figure 4 345 2.3 -55 to 175 A A A A W W/oC
o
Ratings 30 20
Units V V
C
Thermal Characteristics
RJC RJA RJA Thermal Resistance Junction to Case TO-263 Thermal Resistance Junction to Ambient TO-263 Thermal Resistance Junction to Ambient TO-263, 1in2 copper pad area 0.43 62 43
o o o
C/W C/W C/W
Package Marking and Ordering Information
Device Marking N302AS Device ISL9N302AS3ST Package TO-263AB Reel Size 330mm Tape Width 24mm Quantity 800 units
(c)2002 Fairchild Semiconductor Corporation
Rev. B1,April 2002
ISL9N302AS3ST
Electrical Characteristics TA = 25C unless otherwise noted
Symbol Parameter Test Conditions Min Typ Max Units
Off Characteristics
BVDSS IDSS IGSS Drain to Source Breakdown Voltage Zero Gate Voltage Drain Current Gate to Source Leakage Current ID = 250A, VGS = 0V VDS = 25V VGS = 0V VGS = 20V TC = 150o 30 1 250 100 V A nA
On Characteristics
VGS(TH) rDS(ON) Gate to Source Threshold Voltage Drain to Source On Resistance VGS = VDS, ID = 250A ID = 75A, VGS = 10V ID = 75A, VGS = 4.5V 1 3 V 0.0019 0.0023 0.0027 0.0033
Dynamic Characteristics
CISS COSS CRSS Qg(TOT) Qg(5) Qg(TH) Qgs Qgd Input Capacitance Output Capacitance Reverse Transfer Capacitance Total Gate Charge at 10V Total Gate Charge at 5V Threshold Gate Charge Gate to Source Gate Charge Gate to Drain "Miller" Charge VDS = 15V, VGS = 0V, f = 1MHz VGS = 0V to 10V VGS = 0V to 5V V = 15V DD VGS = 0V to 1V ID = 75A Ig = 1.0mA 11000 2000 900 200 110 12 25 31 300 165 18 pF pF pF nC nC nC nC nC
Switching Characteristics (VGS = 4.5V)
tON td(ON) tr td(OFF) tf tOFF Turn-On Time Turn-On Delay Time Rise Time Turn-Off Delay Time Fall Time Turn-Off Time VDD = 15V, ID = 28A VGS = 4.5V, RGS = 1.5 29 120 45 34 224 119 ns ns ns ns ns ns
Switching Characteristics (VGS = 10V)
tON td(ON) tr td(OFF) tf tOFF Turn-On Time Turn-On Delay Time Rise Time Turn-Off Delay Time Fall Time Turn-Off Time VDD = 15V, ID = 28A VGS = 10V, R GS = 1.5 16 120 70 30 204 150 ns ns ns ns ns ns
Unclamped Inductive Switching
tAV Avalanche Time ID = 7.2A, L = 3.0mH 480 s
Drain-Source Diode Characteristics
VSD trr QRR Source to Drain Diode Voltage Reverse Recovery Time Reverse Recovered Charge ISD = 75A ISD = 40A ISD = 75A, dISD /dt = 100A/s ISD = 75A, dISD /dt = 100A/s 1.25 1.0 42 34 V V ns nC
(c)2002 Fairchild Semiconductor Corporation
Rev. B1 April 2002
ISL9N302AS3ST
Typical Characteristic
1.2 80
POWER DISSIPATION MULTIPLIER
1.0 ID, DRAIN CURRENT (A) 60 VGS = 10V
0.8
VGS = 4.5V 40
0.6
0.4
20
0.2
0 0 25 50 75 100 125 150 175 TC , CASE TEMPERATURE (oC)
0 25 50 75 100 125 150 175 TC, CASE TEMPERATURE (o C)
Figure 1. Normalized Power Dissipation vs Ambient Temperature
2 1 DUTY CYCLE - DESCENDING ORDER 0.5 0.2 0.1 0.05 0.02 0.01
Figure 2. Maximum Continuous Drain Current vs Case Temperature
ZJC, NORMALIZED THERMAL IMPEDANCE
PDM 0.1 t1 t2 SINGLE PULSE NOTES: DUTY FACTOR: D = t1/t2 PEAK TJ = PDM x ZJC x RJC + TC 10-2 t , RECTANGULAR PULSE DURATION (s) 10-1 100 101
0.01 10-5
10-4
10-3
Figure 3. Normalized Maximum Transient Thermal Impedance
5000 TC = 25 oC FOR TEMPERATURES ABOVE 25oC DERATE PEAK CURRENT AS FOLLOWS: I = I25 175 - TC 150
TRANSCONDUCTANCE MAY LIMIT CURRENT IN THIS REGION
IDM , PEAK CURRENT (A)
1000
VGS = 10V
VGS = 5V
100 50 10-5 10-4 10-3 10-2 t, PULSE WIDTH (s) 10-1 100 101
Figure 4. Peak Current Capability
(c)2002 Fairchild Semiconductor Corporation
Rev. B1 April 2002
ISL9N302AS3ST
Typical Characteristic (Continued)
150 PULSE DURATION = 80s 125 ID , DRAIN CURRENT (A) DUTY CYCLE = 0.5% MAX VDD = 15V ID, DRAIN CURRENT (A) 125 VGS = 3V 100 150 VGS = 3.5V
100
75 TJ = 25oC 50 TJ = 175 oC 25 TJ = -55oC 0 1.5 2.0 2.5 3.0 3.5 VGS , GATE TO SOURCE VOLTAGE (V)
75 VGS = 4.5V 50 VGS = 10V TC = 25oC PULSE DURATION = 80s DUTY CYCLE = 0.5% MAX 0 0.5 1.0 1.5 2.0
25
0 VDS , DRAIN TO SOURCE VOLTAGE (V)
Figure 5. Transfer Characteristics
10 NORMALIZED DRAIN TO SOURCE ON RESISTANCE PULSE DURATION = 80s DUTY CYCLE = 0.5% MAX 8 rDS(ON), DRAIN TO SOURCE ON RESISTANCE (m) ID = 75A 6 ID = 10A 4
Figure 6. Saturation Characteristics
1.8 1.6 1.4 1.2 1.0 0.8 VGS = 10V, ID = 75A 0.6 -80 -40 0 40 80 120 160 200 PULSE DURATION = 80s DUTY CYCLE = 0.5% MAX
2
0 2 4 6 8 10
VGS, GATE TO SOURCE VOLTAGE (V)
TJ, JUNCTION TEMPERATURE (oC)
Figure 7. Drain to Source On Resistance vs Gate Voltage and Drain Current
1.4 VGS = VDS, ID = 250A 1.2 NORMALIZED GATE THRESHOLD VOLTAGE
Figure 8. Normalized Drain to Source On Resistance vs Junction Temperature
1.2 ID = 250A NORMALIZED DRAIN TO SOURCE BREAKDOWN VOLTAGE
1.0 0.8 0.6 0.4
1.1
1.0
0.2 -80 -40 0 40 80 120 (o C) 160 200
0.9 -80 -40 0 40 80 120 (oC) 160 200
TJ, JUNCTION TEMPERATURE
TJ , JUNCTION TEMPERATURE
Figure 9. Normalized Gate Threshold Voltage vs Junction Temperature
Figure 10. Normalized Drain to Source Breakdown Voltage vs Junction Temperature
(c)2002 Fairchild Semiconductor Corporation
Rev. B1 April 2002
ISL9N302AS3ST
Typical Characteristic (Continued)
20000 VGS , GATE TO SOURCE VOLTAGE (V) 10 VDD = 15V 8
10000 C, CAPACITANCE (pF) CISS = CGS + CGD COSS CDS + C GD
6
4 WAVEFORMS IN DESCENDING ORDER: ID = 75A ID = 28A
CRSS = C GD 1000 VGS = 0V, f = 1MHz 500 0.1 1 10 30
2
0 0 50 100 150 200 250
VDS , DRAIN TO SOURCE VOLTAGE (V)
Qg, GATE CHARGE (nC)
Figure 11. Capacitance vs Drain to Source Voltage
1000 VGS = 4.5V, VDD = 15V, ID = 28A 800 SWITCHING TIME (ns)
Figure 12. Gate Charge Waveforms for Constant Gate Currents
1400 VGS = 10V, VDD = 15V, ID = 28A 1200 SWITCHING TIME (ns) 1000 800 td(OFF) 600 tf 400 tr 200 0 td(ON) 0 10 20 30 40 50
600
tr
tf
400 td(OFF) 200 td(ON) 0 0 10 20 30 40 50
RGS, GATE TO SOURCE RESISTANCE ()
RGS, GATE TO SOURCE RESISTANCE ()
Figure 13. Switching Time vs Gate Resistance
Figure 14. Switching Time vs Gate Resistance
Test Circuits and Waveforms
VDS tP L IAS VARY tP TO OBTAIN REQUIRED PEAK I AS VGS DUT tP 0V RG -
BVDSS
VDS VDD
+
VDD
IAS 0.01
0 tAV
Figure 15. Unclamped Energy Test Circuit
Figure 16. Unclamped Energy Waveforms
(c)2002 Fairchild Semiconductor Corporation
Rev. B1 April 2002
ISL9N302AS3ST
Test Circuits and Waveforms (Continued)
VDS RL
VDD VDS
Qg(TOT)
VGS = 10V VGS Qg(5) VDD DUT Ig(REF) 0 VGS VGS = 1V Qg(TH) Qgs Ig(REF) 0 Qgd VGS = 5V
+
Figure 17. Gate Charge Test Circuit
Figure 18. Gate Charge Waveforms
VDS
tON td(ON) RL VDS 90% tr
tOFF td(OFF) tf 90%
VGS
+
VDD DUT 0
10%
10%
90% VGS 50% PULSE WIDTH 50%
RGS
VGS
0
10%
Figure 19. Switching Time Test Circuit
Figure 20. Switching Time Waveforms
(c)2002 Fairchild Semiconductor Corporation
Rev. B1 April 2002
ISL9N302AS3ST
Thermal Resistance vs. Mounting Pad Area
The maximum rated junction temperature, TJM , and the thermal resistance of the heat dissipating path determines the maximum allowable device power dissipation, PDM , in an application. Therefore the application's ambient temperature, TA (oC), and thermal resistance R JA (oC/W) must be reviewed to ensure that TJM is never exceeded. Equation 1 mathematically represents the relationship and serves as the basis for establishing the rating of the part.
(T -T ) JM A P D M = ----------------------------Z JA
80 RJA = 26.51+ 19.84/(0.262+Area)
60 RJA (oC/W) 40 20 0.1 1 AREA, TOP COPPER AREA (in2) 10
(EQ. 1)
In using surface mount devices such as the TO-263 package, the environment in which it is applied will have a significant influence on the part's current and maximum power dissipation ratings. Precise determination of PDM is complex and influenced by many factors: 1. Mounting pad area onto which the device is attached and whether there is copper on one side or both sides of the board. 2. The number of copper layers and the thickness of the board. 3. The use of external heat sinks. 4. The use of thermal vias. 5. Air flow and board orientation. 6. For non steady state applications, the pulse width, the duty cycle and the transient thermal response of the part, the board and the environment they are in. Fairchild provides thermal information to assist the designer's preliminary application evaluation. Figure 21 defines the RJA for the device as a function of the top copper (component side) area. This is for a horizontally positioned FR-4 board with 1oz copper after 1000 seconds of steady state power with no air flow. This graph provides the necessary information for calculation of the steady state junction temperature or power dissipation. Pulse applications can be evaluated using the Fairchild device Spice thermal model or manually utilizing the normalized maximum transient thermal impedance curve. Displayed on the curve are R JA values listed in the Electrical Specifications table. The points were chosen to depict the compromise between the copper board area, the thermal resistance and ultimately the power dissipation, PDM . Thermal resistances corresponding to other copper areas can be obtained from Figure 21 or by calculation using Equation 2. R JA is defined as the natural log of the area times a coefficient added to a constant. The area, in square inches is the top copper area including the gate and source pads.
Figure 21. Thermal Resistance vs Mounting Pad Area
RJA = 26.51 + ------------------------------------
19.84 ( 0.262 + Area )
(EQ. 2)
(c)2002 Fairchild Semiconductor Corporation
Rev. B1 April 2002
ISL9N302AS3ST
PSPICE Electrical Model
SUBCKT ISL9N302AS3ST 2 1 3 ; CA 12 8 5e-9 Cb 15 14 5.5e-9 Cin 6 8 1e-8 Dbody 7 5 DbodyMOD Dbreak 5 11 DbreakMOD Dplcap 10 5 DplcapMOD Ebreak 11 7 17 18 30.4 Eds 14 8 5 8 1 Egs 13 8 6 8 1 Esg 6 10 6 8 1 Evthres 6 21 19 8 1 Evtemp 20 6 18 22 1 It 8 17 1
LGATE LDRAIN DPLCAP 10 RSLC1 51 ESLC 50 RLDRAIN DBREAK 11 + 17 EBREAK 18 MWEAK MMED MSTRO CIN LSOURCE 8 RSOURCE RLSOURCE S1A 12 13 8 S1B CA 13 + EGS 6 8 EDS S2A 14 13 S2B CB + 5 8 8 RVTHRES 14 IT 15 17 RBREAK 18 RVTEMP 19 VBAT + 22 7 SOURCE 3 5 DRAIN 2
rev May 2001
RSLC2
5 51 ESG + EVTEMP RGATE + 18 22 9 20 RLGATE 6 GATE 1 6 8 -
EVTHRES 16 21 + 19 8
Lgate 1 9 5.618e-9 Ldrain 2 5 1e-9 Lsource 3 7 1.98e-9 RLgate 1 9 56.1 RLdrain 2 5 15 RLsource 3 7 19.8 Mmed 16 6 8 8 MmedMOD Mstro 16 6 8 8 MstroMOD Mweak 16 21 8 8 MweakMOD Rbreak 17 18 RbreakMOD 1 Rdrain 50 16 RdrainMOD 4e-4 Rgate 9 20 5.93e-1 RSLC1 5 51 RSLCMOD 1e-6 RSLC2 5 50 1e3 Rsource 8 7 RsourceMOD 1.3e-3 Rvthres 22 8 RvthresMOD 1 Rvtemp 18 19 RvtempMOD 1 S1a 6 12 13 8 S1AMOD S1b 13 12 13 8 S1BMOD S2a 6 15 14 13 S2AMOD S2b 13 15 14 13 S2BMOD Vbat 22 19 DC 1
ESLC 51 50 VALUE={(V(5,51)/ABS(V(5,51)))*(PWR(V(5,51)/(1e-6*500),3))} .MODEL DbodyMOD D (IS=2e-10 N=1.05 RS=1.8e-3 TRS1=9e-4 TRS2=1e-6 + CJO=4.9e-9 M=4.9e-1 TT=1e-13 XTI=0) .MODEL DbreakMOD D (RS=2.5e-1 TRS1=1e-3 TRS2=-8.9e-6) .MODEL DplcapMOD D (CJO=3.5e-9 IS=1e-30 N=10 M=4.7e-1) .MODEL MstroMOD NMOS (VTO=2.1 KP=550 IS=1e-25 N=10 TOX=1 L=1u W=1u) .MODEL MmedMOD NMOS (VTO=1.6 KP=30 IS=1e-30 N=10 TOX=1 L=1u W=1u RG=5.93e-1) .MODEL MweakMOD NMOS (VTO=1.22 KP=1e-1 IS=1e-40 N=10 TOX=1 L=1u W=1u RG=5.93 RS=1e-1) .MODEL RbreakMOD RES (TC1=1e-3 TC2=-7e-7) .MODEL RdrainMOD RES (TC1=1.2e-2 TC2=2.5e-5) .MODEL RSLCMOD RES (TC1=3.5e-9 TC2=5e-6) .MODEL RsourceMOD RES (TC1=1e-3 TC2=1e-6) .MODEL RvthresMOD RES (TC1=-2.9e-3 TC2=-9e-6) .MODEL RvtempMOD RES (TC1=-1.8e-3 TC2=1e-6) .MODEL S1AMOD VSWITCH (RON=1e-5 ROFF=0.1 VON=-3.5 VOFF=-1.5) .MODEL S1BMOD VSWITCH (RON=1e-5 ROFF=0.1 VON=-1.5 VOFF=-3.5) .MODEL S2AMOD VSWITCH (RON=1e-5 ROFF=0.1 VON=-0.4 VOFF=0.1) .MODEL S2BMOD VSWITCH (RON=1e-5 ROFF=0.1 VON=0.1 VOFF=-0.4) .ENDS NOTE: For further discussion of the PSPICE model, consult A New PSPICE Sub-Circuit for the Power MOSFET Featuring Global Temperature Options; IEEE Power Electronics Specialist Conference Records, 1991, written by William J. Hepp and C. Frank Wheatley.
(c)2002 Fairchild Semiconductor Corporation
+
RDRAIN
DBODY
Rev. B1 April 2002
ISL9N302AS3ST
SABER Electrical Model
REV May 2001 template ISL9N302AS3ST n2,n1,n3 electrical n2,n1,n3 { var i iscl dp..model dbodymod = (isl=2e-10,nl=1.05,rs=1.8e-3,trs1=9e-4,trs2=1e-6,cjo=4.9e-9,m=4.9e-1,tt=1e-13,xti=0) dp..model dbreakmod = (rs=2.5e-1,trs1=1e-3,trs2=-8.9e-6) dp..model dplcapmod = (cjo=3.5e-9,isl=10e-30,nl=10,m=4.7e-1) m..model mstrongmod = (type=_n,vto=2.1,kp=550,is=1e-25, tox=1) m..model mmedmod = (type=_n,vto=1.6,kp=30,is=1e-30, tox=1) m..model mweakmod = (type=_n,vto=1.22,kp=1e-1,is=1e-40, tox=1,rs=1e-1) sw_vcsp..model s1amod = (ron=1e-5,roff=0.1,von=-3.5,voff=-1.5) sw_vcsp..model s1bmod = (ron=1e-5,roff=0.1,von=-1.5,voff=-3.5) LDRAIN sw_vcsp..model s2amod = (ron=1e-5,roff=0.1,von=-0.4,voff=0.1) DPLCAP 5 DRAIN sw_vcsp..model s2bmod = (ron=1e-5,roff=0.1,von=0.1,voff=-0.4) 2 c.ca n12 n8 = 5e-9 10 c.cb n15 n14 = 5.5e-9 RLDRAIN RSLC1 c.cin n6 n8 = 1e-8
51 RSLC2
dp.dbody n7 n5 = model=dbodymod dp.dbreak n5 n11 = model=dbreakmod dp.dplcap n10 n5 = model=dplcapmod spe.ebreak n11 n7 n17 n18 = 30.4 spe.eds n14 n8 n5 n8 = 1 spe.egs n13 n8 n6 n8 = 1 spe.esg n6 n10 n6 n8 = 1 spe.evthres n6 n21 n19 n8 = 1 spe.evtemp n20 n6 n18 n22 = 1 i.it n8 n17 = 1 l.lgate n1 n9 = 5.618e-9 l.ldrain n2 n5 = 1e-9 l.lsource n3 n7 = 1.98e-9 res.rlgate n1 n9 = 56.1 res.rldrain n2 n5 = 15 res.rlsource n3 n7 = 19.8
ESG
ISCL 6 8 + LGATE 50 RDRAIN EVTHRES 16 21 + 19 8 6 MMED MSTRO CIN 8 RSOURCE RLSOURCE S1A 12 13 8 S1B CA 13 + EGS 6 8 EDS S2A 14 13 S2B CB + 5 8 8 22 RVTHRES 14 IT VBAT + 15 17 RBREAK 18 RVTEMP 19 DBREAK 11 DBODY MWEAK EBREAK + 17 18 LSOURCE 7 SOURCE 3
GATE 1 RLGATE
EVTEMP RGATE + 18 22 9 20
m.mmed n16 n6 n8 n8 = model=mmedmod, l=1u, w=1u m.mstrong n16 n6 n8 n8 = model=mstrongmod, l=1u, w=1u m.mweak n16 n21 n8 n8 = model=mweakmod, l=1u, w=1u res.rbreak n17 n18 = 1, tc1=1e-3,tc2=-7e-7 res.rdrain n50 n16 = 4e-4, tc1=1.2e-2,tc2=2.5e-5 res.rgate n9 n20 = 5.93e-1 res.rslc1 n5 n51 = 1e-6, tc1=3.5e-9,tc2=5e-6 res.rslc2 n5 n50 = 1e3 res.rsource n8 n7 = 1.3e-3, tc1=1e-3,tc2=1e-6 res.rvthres n22 n8 = 1, tc1=-2.9e-3,tc2=-9e-6 res.rvtemp n18 n19 = 1, tc1=-1.8e-3,tc2=1e-6 sw_vcsp.s1a n6 n12 n13 n8 = model=s1amod sw_vcsp.s1b n13 n12 n13 n8 = model=s1bmod sw_vcsp.s2a n6 n15 n14 n13 = model=s2amod sw_vcsp.s2b n13 n15 n14 n13 = model=s2bmod
v.vbat n22 n19 = dc=1 equations { i (n51->n50) +=iscl iscl: v(n51,n50) = ((v(n5,n51)/(1e-9+abs(v(n5,n51))))*((abs(v(n5,n51)*1e6/500))** 3)) }
(c)2002 Fairchild Semiconductor Corporation
Rev. B1 April 2002
ISL9N302AS3ST
SPICE Thermal Model
REV May 2001 ISL9N302AS3ST CTHERM1 th 6 4.5e-3 CTHERM2 6 5 2e-2 CTHERM3 5 4 1.5e-2 CTHERM4 4 3 2.5e-2 CTHERM5 3 2 7e-2 CTHERM6 2 tl 2.5e-1 RTHERM1 th 6 2e-3 RTHERM2 6 5 8.5e-3 RTHERM3 5 4 6e-2 RTHERM4 4 3 8e-2 RTHERM5 3 2 9e-2 RTHERM6 2 tl 1e-1
th
JUNCTION
RTHERM1
CTHERM1
6
RTHERM2
CTHERM2
5
SABER Thermal Model
SABER thermal model ISL9N302AS3ST template thermal_model th tl thermal_c th, tl { ctherm.ctherm1 th 6 = 4.5e-3 ctherm.ctherm2 6 5 = 2e-2 ctherm.ctherm3 5 4 = 1.5e-2 ctherm.ctherm4 4 3 = 2.5e-2 ctherm.ctherm5 3 2 = 7e-2 ctherm.ctherm6 2 tl = 2.5e-1 rtherm.rtherm1 th 6 =2e-3 rtherm.rtherm2 6 5 = 8.5e-3 rtherm.rtherm3 5 4 = 6e-2 rtherm.rtherm4 4 3 = 8e-2 rtherm.rtherm5 3 2 = 9e-2 rtherm.rtherm6 2 tl = 1e-1 }
RTHERM3
CTHERM3
4
RTHERM4
CTHERM4
3
RTHERM5
CTHERM5
2
RTHERM6
CTHERM6
tl
CASE
(c)2002 Fairchild Semiconductor Corporation
Rev. B1 April 2002
TRADEMARKS
The following are registered and unregistered trademarks Fairchild Semiconductor owns or is authorized to use and is not intended to be an exhaustive list of all such trademarks.
ACEx Bottomless CoolFET CROSSVOLT DenseTrench DOME EcoSPARK E2CMOSTM EnSignaTM FACT FACT Quiet Series
DISCLAIMER
FAST a FASTr FRFET GlobalOptoisolator GTO HiSeC I2C ISOPLANAR LittleFET MicroFET MicroPak
MICROWIRE OPTOLOGIC a OPTOPLANAR PACMAN POP Power247 PowerTrench a QFET QS QT Optoelectronics Quiet Series
SILENT SWITCHER a UHC SMART START UltraFET a SPM VCX STAR*POWER Stealth SuperSOT-3 SuperSOT-6 SuperSOT-8 SyncFET TinyLogic TruTranslation
STAR*POWER is used under license
FAIRCHILD SEMICONDUCTOR RESERVES THE RIGHT TO MAKE CHANGES WITHOUT FURTHER NOTICE TO ANY PRODUCTS HEREIN TO IMPROVE RELIABILITY, FUNCTION OR DESIGN. FAIRCHILD DOES NOT ASSUME ANY LIABILITY ARISING OUT OF THE APPLICATION OR USE OF ANY PRODUCT OR CIRCUIT DESCRIBED HEREIN; NEITHER DOES IT CONVEY ANY LICENSE UNDER ITS PATENT RIGHTS, NOR THE RIGHTS OF OTHERS.
LIFE SUPPORT POLICY FAIRCHILDS PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF FAIRCHILD SEMICONDUCTOR CORPORATION. As used herein: 2. A critical component is any component of a life 1. Life support devices or systems are devices or support device or system whose failure to perform can systems which, (a) are intended for surgical implant into be reasonably expected to cause the failure of the life the body, or (b) support or sustain life, or (c) whose support device or system, or to affect its safety or failure to perform when properly used in accordance with instructions for use provided in the labeling, can be effectiveness. reasonably expected to result in significant injury to the user. PRODUCT STATUS DEFINITIONS Definition of Terms Datasheet Identification Advance Information Product Status Formative or In Design First Production Definition This datasheet contains the design specifications for product development. Specifications may change in any manner without notice. This datasheet contains preliminary data, and supplementary data will be published at a later date. Fairchild Semiconductor reserves the right to make changes at any time without notice in order to improve design. This datasheet contains final specifications. Fairchild Semiconductor reserves the right to make changes at any time without notice in order to improve design. This datasheet contains specifications on a product that has been discontinued by Fairchild semiconductor. The datasheet is printed for reference information only.
Preliminary
No Identification Needed
Full Production
Obsolete
Not In Production
Rev. H5

▲Up To Search▲

Price & Availability of ISL9N302AS3ST

	To Download ISL9N302AS3ST Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .